Move the ball

To keep constantly updating the canvas drawing on each frame, we need to define a drawing function that will run over and over again, with a different set of variable values each time to change sprite positions, etc. You can run a function over and over again using a JavaScript timing function such as setInterval() or requestAnimationFrame().

Delete all the JavaScript you currently have inside your HTML file except for the first two lines, and add the following below them. The draw() function will be executed within setInterval every 10 milliseconds:

function draw() {
  // drawing code
}
setInterval(draw, 10);

Thanks to the infinite nature of setInterval the draw() function will be called every 10 milliseconds forever, or until we stop it. Now, let's draw the ball — add the following inside your draw() function:

ctx.beginPath();
ctx.arc(50, 50, 10, 0, Math.PI * 2);
ctx.fillStyle = "#0095DD";
ctx.fill();
ctx.closePath();

Try your updated code now — the ball should be repainted on every frame.

You won't notice the ball being repainted constantly at the moment, as it's not moving. Let's change that. First, instead of a hardcoded position at (50,50) we will define a starting point at the bottom center part of the Canvas in variables called x and y, then use those to define the position the circle is drawn at.

First, add the following two lines above your draw() function, to define x and y:

let x = canvas.width / 2;
let y = canvas.height - 30;

Next update the draw() function to use the x and y variables in the arc() method, as shown in the following highlighted line:

function draw() {
  ctx.beginPath();
  ctx.arc(x, y, 10, 0, Math.PI * 2);
  ctx.fillStyle = "#0095DD";
  ctx.fill();
  ctx.closePath();
}

Now comes the important part: we want to add a small value to x and y after every frame has been drawn to make it appear that the ball is moving. Let's define these small values as dx and dy and set their values to 2 and -2 respectively. Add the following below your x and y variable definitions:

let dx = 2;
let dy = -2;

The last thing to do is to update x and y with our dx and dy variable on every frame, so the ball will be painted in the new position on every update. Add the following two new lines indicated below to your draw() function:

function draw() {
  ctx.beginPath();
  ctx.arc(x, y, 10, 0, Math.PI * 2);
  ctx.fillStyle = "#0095DD";
  ctx.fill();
  ctx.closePath();
  x += dx;
  y += dy;
}

Save your code again and try it in your browser. This works OK, although it appears that the ball is leaving a trail behind it:

The ball is leaving a trail because we're painting a new circle on every frame without removing the previous one. Don't worry, because there's a method to clear canvas content: clearRect(). This method takes four parameters: the x and y coordinates of the top left corner of a rectangle, and the x and y coordinates of the bottom right corner of a rectangle. The whole area covered by this rectangle will be cleared of any content previously painted there.

Add the following highlighted new line to the draw() function:

function draw() {
  ctx.clearRect(0, 0, canvas.width, canvas.height);
  ctx.beginPath();
  ctx.arc(x, y, 10, 0, Math.PI * 2);
  ctx.fillStyle = "#0095DD";
  ctx.fill();
  ctx.closePath();
  x += dx;
  y += dy;
}

Save your code and try again, and this time you'll see the ball move without a trail. Every 10 milliseconds the canvas is cleared, the blue circle (our ball) will be drawn on a given position and the x and y values will be updated for the next frame.

We will be adding more and more commands to the draw() function in the next few articles, so it's good to keep it as simple and clean as possible. Let's start by moving the ball drawing code to a separate function.

Replace the existing draw() function with the following two functions:

function drawBall() {
  ctx.beginPath();
  ctx.arc(x, y, 10, 0, Math.PI * 2);
  ctx.fillStyle = "#0095DD";
  ctx.fill();
  ctx.closePath();
}

function draw() {
  ctx.clearRect(0, 0, canvas.width, canvas.height);
  drawBall();
  x += dx;
  y += dy;
}

You can check the finished code for this article for yourself in the live demo below, and play with it to understand better how it works:

We've drawn our ball and gotten it moving, but it keeps disappearing off the edge of the canvas. In the third chapter we'll explore how to make it bounce off the walls.

• « Previous
• Next »